Meinberg LANTIME M300/RDT, 19" rack NTP Time Server Meinberg LANTIME M300/RDT, 19" rack NTP Time Server

Meinberg LANTIME M300/RDT, 19" rack

NTP Time Server

Varenr: M300/RDT
Meinberg LANTIME M300/RDT NTP Time Server
Syncronised by External Meinberg radio clock (Stratum 1 mode) or
up to 7 external NTP time servers (Stratum 2 mode). 
 
Description
The GNU/Linux operating system of the LANTIMEs SBC (Single Board Computer) has been optimized to ensure a high level of security and reliability. A large display shows the state of the NTP subsystem.
 
The configuration of the system can be done by using a standard web browser to access the extensive but straightforward html interface. Alternatively a text based and menu driven setup utility can be started from the shell prompt after logging into the unit via Telnet or SSH.
 
The security-related features of LANTIME time servers satisfy highest demands. The time synchronization data can be reliably signed and secured by symmetric keys (MD5) and the NTP autokey procedures. This protects the clients against manipulated time and man-in-the-middle attacks and allows them to verify that the NTP packets they received were send by the LANTIME. Additionally the whole LANTIME configuration can be done by using encrypted channels (e.g. SSH, HTTPS or SNMPv3). Every unused/unneeded protocol can be disabled in order to reduce possible points of attack.
 
LANTIME time servers are designed to be deployed in IPv6 networks, the NTP time synchronization as well as the configuration interfaces (Web-based, SSH and SNMP) comes with IPv6 support. You can assign several IPv6 addresses and the system supports automatic configuration by IPv6 autoconf.
 
Because of its modular system architecture it is possible to equip a LANTIME time server with up to two additional ethernet ports, even fiber optic network ports are available as an option.
 
Characteristics
Display: LC-display, 2 x 40 characters, with backlight
Control elements: Eight push buttons to set up basic network parameters and to change receiver settings
Status info: Four bicolor LEDs showing status of:
- reference time
- time service
- network
- alarm
 
Pulse Synchronization Input Signals: PPS (PulsePerSecond) reference signal via BNC connector
 
Interface: Two independent RS232 interfaces for external reference signal
 
Network Interface: 2 x 10/100 MBit with RJ45
 
Power supply: 85-264VAC (50/60Hz)
 
Universal Serial Bus (USB) Ports: 1x USB Port in front panel:
- install firmware upgrades
- backup and restore configuration files
- copy security keys
- lock/unlock front keys
 
Single-Board-Computer: i386 compatible 500Mhz CPU, 128 MB RAM
Operating System of the SBC: Linux with nano kernel (incl. PPSkit)
Network protocols OSI Layer 4 (transport layer): TCP, UDP
Network protocols OSI Layer 7 (application layer): TELNET, FTP, SSH (incl. SFTP, SCP), HTTP, HTTPS, SYSLOG, SNMP
Internet Protocol (IP): IP v4, IP v6
Network Autoconfiguration Support: IPv4: Dynamic Host Configuration Protocol - DHCP (RFC 2131)
IPv6: Autoconfiguration Networking - AUTOCONF
 
Network Time Protocol (NTP): NTP v2 (RFC 1119), NTP v3 (RFC 1305), NTP v4 (no RFC)
SNTP v3 (RFC 1769), SNTP v4 (RFC 2030)
MD5 Authentication and Autokey Key Management
Time Protocol (TIME): Time Protocol (RFC 868)
Daytime Protocol (DAYTIME): Daytime Protocol (RFC 867)
IEC 61850: Synchronization of IEC 61850 compliant devices by using SNTP
Hypertext Transfer Protocol (HTTP): HTTP/HTTPS (RC 2616)
Secure Shell (SSH): SSH v1.3, SSH v1.5, SSH v2 (OpenSSH)
Telnet: Telnet (RFC 854-RFC 861)
Simple Network Management Protocol (SNMP): SNMPv1 (RFC 1157), SNMPv2c (RFC 1901-1908), SNMP v3 (RFC 3411-3418)
 
Form Factor: 19'' aluminium case (1U) Schroff Multipac
 
Ambient temperature: 0 ... 50°C / 32 ... 122°F
 
Humidity: Max. 85%
 
Scope of supply: Time Server, power cable and a USB storage device with Quick-Start Guide and a detailed reference manual as PDF file in the "Manual" folder.
 
Technical Support: Meinberg offers free lifetime technical support via telephone or e-mail.
 
Warranty: Three-Year Warranty
 
Firmware Updates: Firmware is field-upgradeable, updates can be installed directly at the unit or via a remote network connection.
Software updates are provided free of charge, for the lifetime of your Meinberg product.